|
|
BB-200
WARM WATER BIDET
Available in White
|
|
|
(Retail Price $249.00)
$129.95 each
|
BB-200
Installation
|
|
| Installation
Instructions |
|
| What
you have |
|
|
|
|
|
|
Flexible
Hoses
7/8"x3/8"
1/2"x3/8"
|
(2)
Adapters with
emergency shut valve
|
10'
White tube
|
(3)
Rubber seal
|
(2)
1/2" Converter
|
|
| What
you need |
|
|
|
|
|
|
|
Teflon
Tape
|
Screw
Driver
|
Wrench
|
Cutter
|
Compression
Fitting
|
Velcro
Tape
(optional)
|
|
|
| First
things first. |
Locate hot water source and make sure supplied
10 feet of white tube is enough to connect both
hot and cold water to BB-200.
Should you need extra length of
tube, contact customer service or distributor in
you area for immediate supply. Compression
fitting is not standard supply. Be sure to
have it before cutting pipe. |
|
| Installation |
|
|
|
1.
Shut off the water valve.
2.
Measure and cut copper pipe using
cutter.
3.
Unscrew and detach bolt.
4.
Apply bolt first, then slide compression
fitting.
5.
Slide down and fit it to top thread of
adapter.
(copper pipe must be
straight to thread)
6.
Insert packing into bottom of adapter as
illustrated,
then tighten adapter
to main water valve.
 Avoid
having tube inlet addressed directly to
top of water valve to turn it back on
freely.
You
can now close emergency shut off valve
and turn on main water valve to
test if
there is any leak.
|
|
|
Insert one end of the white tube into
adapter inlet with nut as shown, the
insert the other end
to BB-200 hot water inlet.
Use
Velcro tape to secure white tube to edge
of wall.
This will
prevent accidental unplugging tube and
tube from hanging.
|
|
|
If you have a flexible metal hoes
instead of copper pipe,
simply substitute it
with supplied flexible hose with packing
inserted.
For
cold water connection, please refer to
BB-50 installation page.
|
|
| Ready?
Go! |
|
|
Trying your Bio-Bidet for the first
time.
Congratulations!
Your are ready to use the Bio-Bidet for
the first time.
IT IS
VERY IMPORTANT THAT YOU USE "NOZZLE
CLEANING" EVERY TIME YOU
USE BB-200. IT WILL:
1. PREVENT ACCIDENTAL NOZZLE
CLOGGING.
2. PREVENT TOILET CLOGGING.
3. IT WILL BRING UP ENOUGH HOT
WATER TO PROVIDE YOU WARM
WATER
WHEN YOU ARE READY TO CLEAN
YOURSELF.
To use it, simply pull it up all the way
residual cold water is drained and
warm water starts to run through.
 You
must push it down before adjusting water
pressure.
|
|
Using 1/2" Converter
|
|
|
If
your main water line has 1/2" male
thread instead of 3/8", simply
convert it to 3/8"
using supplied converter.
Simply
insert converter in between main water
line hose as illustrated.
have
further questions or need assistance?
Contact any of our distributors in you
area or a representative at our main
office.
We
are there to help with your questions.
|
|
|
|
Trouble Shooting |
|
|
|
|
|
If
your spray nozzle is clogged, you can
remove the spray outlet by turning it 90
degree
counter clockwise and pulling it down.
After cleaning it, put it back an turn
90 degree
clockwise to lock.
You can select two different water spray
angles by pulling the spray outlet tip
up
or pushing it back as illustrated. |
|
FINAL
ASSEMBLED FIGURE.
|
